fbpx Pre-Stain Wood Conditioner |General Finishes | General Finishes


                                    Oil Based Pre-Stain Wood Conditioner

                                    Pre-Stain Wood Conditioner is designed for use before staining new, soft and porous wood surfaces, such as aspen, cherry, birch, poplar or pine with an oil-based stain. It penetrates the grain of the wood to promote uniform acceptance of oil-based wood stain?and reduces streaking and blotching to help ensure beautiful, even coverage.

                                    Find A Store Compare Similar Products
                                    General Finishes Natural Oil Based Pre-Stain Wood Conditioner, Quart


                                    Step 1: Preparation

                                    All raw wood projects require preparation sanding before applying stain?or wood conditioners.?If you skip this critical step, your finish may be rough and uneven.

                                    Preparation for Raw Wood Projects Prior to the Application of an Oil-based Stain
                                    See our video: How to Prep Sand Raw Wood

                                    1. Prep sand with 120-grit sandpaper?followed by 150-grit sandpaper.
                                    2. Remove dust with a vacuum, compressed air, a tack cloth or a water-dampened rag.??
                                    3. Do not over-sand with fine-grit sandpapers; this will close and seal the wood grain, preventing ideal product absorption.

                                    Preparation of An Existing Butcher Block Surface

                                    1. Remove any food residue using a pastry scraper or spatula to gently scrape the countertop in areas where you find dried-on food or residue. Avoid gouging the wood by keeping the blade at an angle that just?skims the surface.
                                    2. Scrub the countertop?using a scrub brush, Scotch Brite Pad or sponge and scrub the countertop with hot water and mild dish soap.
                                    3. Rinse with hot water: Run a clean dishcloth through hot water and rinse the countertop several times.
                                    4. Dry thoroughly with a clean dish towel or paper towel.

                                    How To Apply General Finishes Oil Based Pre-Stain Conditioner

                                    General Finishes Oil Based Pre-Stain Conditioner Application Steps

                                    For use with oil-based stains.

                                    1. Stir General Finishes Oil Based Pre-Stain Conditioner to reincorporate solids that have settled to the bottom of the can.
                                    2. Do NOT thin.
                                    3. Apply 1 coat of Pre-Stain Conditioner to raw wood using a clean cloth, a foam brush?or paint pad applicator.
                                    4. Pre-Stain Conditioner Natural can improve color uniformity over difficult-to-stain wood species such as pine. However, it will limit color absorption, so a darker wood stain may be required to get the desired depth of color.
                                    5. Let Pre-Stain Conditioner penetrate the wood for 10+ minutes.
                                    6. Wipe off excess with a clean, dry cloth.
                                    7. Let Pre-Stain Conditioner dry at least 30?minutes, but no longer than 2 hours before applying stain, in ideal conditions: 70°F/20°C; 50-70% humidity. Do not wait longer than 2 hours, and never let Pre-Stain Conditioner dry overnight before applying a stain over it.

                                    Cleanup of Oil Based Products

                                    Clean up application materials and hands with mineral spirits or?waterless hand cleaner, like Goop or Gojo.?

                                    Take great care when disposing of product-soaked applicators. Application materials, such as brushes and towels, containing oil-based products?may spontaneously catch fire if improperly discarded. Immediately place all application materials soaked with this product in a sealed, water-filled metal container. Dispose of in accordance with local fire regulations.?

                                    Clean up spills with mineral spirits immediately while wet. If oil-based finishes dry, they are difficult to clean off any surface, clothes or carpet. Carpet may discolor if cleaned with mineral spirits.

                                    Protect your workspace with a tarp, your hands with gloves, and your clothes with an apron.

                                    Storage of Oil Based Products

                                    Life of Product
                                    General Finishes products do not last forever, even when unopened. They are?best used within 1 year of the manufacture date listed on the bottom of the can. The life of the product may be extended with proper care and storage.

                                    Storage Tips
                                    See our video: Tips for Storing Leftover Finishes
                                    Oil-based?products?start to harden and cure when exposed to oxygen. The following best practices will increase the life of your product:

                                    1. Keep container tightly closed and sealed until ready for use, in the original container.?Do not store in unlabeled containers.
                                    2. Pry open sealed lids with a paint can opener by hooking under the lid's rolled edge. The use of a screwdriver can disfigure the rim and lid, impairing a complete seal.?
                                    3. Keep lid closed while working. Decant what you will use into a bowl, paper cup, or plate, and close can lid as you work. Every minute the can is open, the product is curing.
                                    4. Containers that have been opened must be carefully resealed and kept upright to prevent leakage. Clean the chime of the can?thoroughly with a paper towel before closing to create a complete?seal. Product in the chime can?be minimized by using a pouring lid, such as Fitsall. Avoid wiping used brushes on the lid.
                                    5. Pound the lid in place?using a rubber mallet to avoid distorting the chime or lid. Dents in the lid from direct contact with a hammer can impair a complete seal. Alternatively, place a flat piece of wood over can lid and firmly pound shut.
                                    6. Avoid temperatures below 50°F/10°C or above 80°F/26°C. Frozen and heat-damaged product cannot be revitalized. Store?in original container protected from direct sunlight in a dry, cool and well-ventilated areas.
                                    7. Do not store product in an attic, garage, in direct sunlight, or next to?ignition source?with heat and flames such as a furnace.?
                                    8. Store?the can upside down to create a liquid seal, minimizing oxygen exposure from within the can.?Decant remaining product from the can before stirring.
                                    9. Add Bloxygen can.?Bloxygen is an argon gas system that prevents oxygen and moisture from hardening leftover product. Because Bloxygen gas is heavier than air, it sinks to the surface of the leftover finish, creating a barrier between product and air trapped in the container.
                                    10. Decant leftovers to a smaller, properly labeled container when the?finish is almost used up to reduce the volume of oxygen in?the container.
                                    11. Use appropriate containment to avoid environmental contamination.

                                    Warnings and Warranties

                                    Oil-Based Pre-Stain Conditioner Warnings and Warranties

                                    Limited Warranty
                                    General Finishes products must be tested to your complete satisfaction before using. General Finishes will not be responsible for color satisfaction, misapplication, nor compatibility with other manufacturers' products. General Finishes will be responsible only for the cost of our products, and not for costs such as labor, damage or project replacement.

                                    Contamination and Compatibility
                                    Our finishes are engineered as a system and are compatible with each other. General Finishes cannot guarantee an ideal refinish when applying our products on top of or combined with another company's products or over surfaces that have been in contact with waxes, polishes or sprays containing contaminants such as silicone. Test for adherence and aesthetics before beginning.

                                    FIRST AID: Seek immediate medical attention if symptoms occur due to the following. EYE CONTACT: Remove any contact lenses. Flush eyes with water for 20+ minutes while lifting upper and lower eyelids. SKIN CONTACT: Wash thoroughly after handling. INHALATION: Move to fresh air. Loosen tight clothing. If not breathing, if breathing is irregular, or if respiratory arrest occurs, trained personnel should provide artificial respiration or oxygen. INGESTION: Call physician immediately. Wash out mouth with water. Do not induce vomiting unless directed to do so by medical personnel. Never give anything by mouth to an unconscious person.

                                    Prop 65 WARNING: This product can expose you to Ethylbenzene, which is known to the State of California to cause cancer. For more information go to www.P65Warnings.ca.gov.


                                    DANGER: Can enter lungs and cause damage.
                                    DANGER: Keep out of reach of children. Keep away from heat and flame. Use only with adequate ventilation. Do not breathe vapor or mist. Do not swallow. Avoid contact with eyes. Keep container tightly closed when not in use. Wash thoroughly after handling.


                                    Basic Features
                                    Product Colors Amber (dries amber)
                                    Base Type Oil
                                    Ambering Yes
                                    Interior or Exterior Interior/Exterior
                                    Type Wood Conditioner
                                    Coats 1 coat
                                    Application Method Brush, Roll
                                    Brushable Yes
                                    Usable over existing finishes No
                                    Sprayable No
                                    Dry Time
                                    Dry Time - Touch 30+ min.
                                    Dry Time - Recoat 30-120 min. before adding stain (no longer than 2 hrs, no less than 30 min.)
                                    Can Sizes Half-Pints, Pints, Quarts
                                    Coverage 45-50 sq.ft./half pint, 180-200 sq.ft./quart
                                    Technical Data
                                    VOC US VOC
                                    <686.514 g/L

                                                                        Real estate


                                                                        Go abroad

                                                                        Second-hand housing


                                                                        Buy a car

                                                                        Mobile phone